|
|
|
||
Last update: Kopecký Dušan doc. Ing. Ph.D. (06.03.2018)
|
|
||
Last update: Kopecký Dušan doc. Ing. Ph.D. (06.03.2018)
Students will be able to:
Analyze the static and dynamic properties of the control loop.
Understand principles of sensors used for measurements of basic technological quantities (temperature, pressure, flow, level, composition).
Set PID controller.
Understand basics of logical and computer control of technological processes. |
|
||
Last update: Kopecký Dušan doc. Ing. Ph.D. (13.02.2018)
měřicí technika měření technologických veličin měření teploty, tlaku, průtoku, hladiny, složení řídicí technika regulované soustavy, vytváření matematických modelů PID regulátor regulační obvod logické řízení počítačové řízení |
|
||
Last update: Kopecký Dušan doc. Ing. Ph.D. (06.03.2018)
Basics: B: Kadlec K., Kmínek M., Kadlec P. (ed) a kolektiv: Měření a řízení chemických, potravinářských a biotechnologických procesů. Díl I. Provozní měření. KEY Publishing Ostrava(2017), ISBN 978-80-7418-284-6. B: Kadlec K., Kmínek M., Kadlec P. (ed) a kolektiv: Měření a řízení chemických, potravinářských a biotechnologických procesů. Díl II. Řízení technologických procesů. Key Publishing Ostrava (2017), ISBN 978-80-7418-285-3. B: Kadlec K., Kmínek M.: Měřicí a řídicí technika, http://uprt.vscht.cz/ucebnice/mce/ B: Kadlec K., Měření technologických veličin (studijní materiály na internetu), https://ufmt.vscht.cz/index.php/cs/elektronicke-pomucky B: Kmínek M., Nachtigalová I.: Řízení technologických procesů (studijní materiály na internetu), http://uprt.vscht.cz/ucebnice/mce/
Complementary: C: Altmann W.: Practical Process Control for Engineers and technicians. Elsevier, Amsterdam, 2005, ISBN 0750664002. C: Lipták B. G., Venzcel K.: Instruments and Automation Engineers’s Handbook 5th. ed. CRC Press, 2017, ISBN 978-1-4987-2764-8. C: Tůma J., R. Wagnerová, R. Farana, L. Landryová: Základy automatizace. ISBN 978-80-248-1523-7. Učební text VŠB. Dostupné také z: http://www.elearn.vsb.cz/archivcd/FS/Zaut/Skripta_text.pdf |
|
||
Last update: Kopecký Dušan doc. Ing. Ph.D. (06.03.2018)
Education support: http://ufmt.vscht.cz/index.php/cs/elektronicke-pomucky http://uprt.vscht.cz/ucebnice/mrt/predn/F0-txt-Bc.htm http://moodle.vscht.cz/course/view.php?id=42 |
|
||
Last update: Kopecký Dušan doc. Ing. Ph.D. (13.02.2018)
Výuku předmětu zajišťují Ústav fyziky a měřicí techniky spolu s Ústavem počítačové a řídicí techniky. Studijní texty k přednáškám jsou k disposici na internetu. |
|
||
Last update: Kopecký Dušan doc. Ing. Ph.D. (13.02.2018)
Zkouška je ústní, otázky u zkoušky zahrnují problematiku podle sylabu předmětu a ke studiu jsou postačující podkladové materiály k přednáškám, případně elektronická učebnice Měřicí a řídicí technika. |
|
||
Last update: Kopecký Dušan doc. Ing. Ph.D. (06.03.2018)
Lectures:
1. Tasks of measurement and control, technological diagrams
2. Analysis of technological systems, creation of mathematical models
3. Simulation of dynamic behavior of systems, dynamic properties of systems, classification of systems according to their dynamic properties
4. Controllers, their properties and uses, actuators
5. Regulatory circuit, regulation process, regulation of typical technological apparatuses
6. Digital control, microprocessor controllers, adaptive control
7. Measurement chain, microprocessor-controlled devices
8. Temperature measurement, contact and non-contact thermometers
9. Pressure measurement, intelligent pressure transducer
10. Level measurement
11. Measurement of flow and total volume
12. Measurement of concentration quantities, chemical sensors, gas and liquid analyzers
13. Combination and sequential logic control, programmable logic controllers
14. Integrated computer control and information systems, data acquisition and processing
Exercises
1. Design of technological schemes in Microsoft VISIO I
2. Design of technological schemes in Microsoft VISIO II
3. Design of technological schemes in Microsoft VISIO III
4. Mathematical modeling of processes using Matlab I software
5. Mathematical modeling of processes using Matlab II software
6. Simulation of processes in Matlab SIMULINK I environment
7. Simulation of processes in Matlab SIMULINK II environment
8. Simulation of processes in Matlab SIMULINK III environment
9. Simulation of processes in Matlab SIMULINK IV environment
10. Data acquisition and processing in LabVIEW I software
11. Data acquisition and processing in LabVIEW II software
12. Data acquisition and processing in LabVIEW III software
13. Data acquisition and processing in LabVIEW IV software
14. Data acquisition and processing in LabVIEW V software |
|
||
Last update: Kopecký Dušan doc. Ing. Ph.D. (06.03.2018)
Mathematics, Physics, or Chemical Engineering and Physical Chemistry |
|
||
Last update: Kopecký Dušan doc. Ing. Ph.D. (06.03.2018)
Matematika I Fyzika I |
|
||
Last update: Kopecký Dušan doc. Ing. Ph.D. (06.03.2018)
Passing the exam. |
Teaching methods | ||||
Activity | Credits | Hours | ||
Konzultace s vyučujícími | 0.2 | 5 | ||
Účast na přednáškách | 1 | 28 | ||
Příprava na přednášky, semináře, laboratoře, exkurzi nebo praxi | 1 | 28 | ||
Příprava na zkoušku a její absolvování | 1.3 | 35 | ||
Účast na seminářích | 0.5 | 14 | ||
4 / 4 | 110 / 112 |
Coursework assessment | |
Form | Significance |
Regular attendance | 20 |
Oral examination | 80 |